ISCSI/LIO

The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.

LIO (LinuxIO) is the in-kernel iSCSI target (since Linux 2.6.38).

Installation

The iSCSI target fabric is included since Linux 3.1.

The important kernel modules are target_core_mod and iscsi_target_mod, which should be in the kernel and loaded automatically.

It is highly recommended to use the free branch versions of the packages: targetcli-fb^AUR, python-rtslib-fb^AUR and python-configshell-fb^AUR.

Start/enable the target.service, included in python-rtslib-fb^AUR, to load necessary modules, mount the configfs and load previously saved iSCSI target configuration.

targetcli

Run targetcli status as root to see some information about the running configuration.

You can use targetcli to create the whole configuration, see targetcli(8).

The config shell creates most names and numbers for you automatically, but you can also provide your own settings. At any point in the shell you can type help in order to see what commands you can issue here.

Tip: In this shell you can use tab-completion and type cd to view & select paths.

After starting the target (see above) you enter the configuration shell with

# targetcli

In this shell you include a block device (here: /dev/disk/by-id/md-name-nas:iscsi) to use with

/> cd backstores/block
/backstores/block> create md_block0 /dev/disk/by-id/md-name-nas:iscsi

Note: You can use any block device, also RAID and LVM devices. You can also use files when you go to fileio instead of block.

You then create an iSCSI Qualified Name (IQN) and a target portal group (TPG) with:

...> cd /iscsi
/iscsi> create

Note: With appending an IQN of your choice to create you can keep targetcli from automatically creating an IQN.

In order to tell LIO that your block device should get used as backstore for the target you issue

Note: Remember that you can type cd to select the path of your <iqn>/tpg1

.../tpg1> cd luns
.../tpg1/luns> create /backstores/block/md_block0

Then you need to create a portal, making a daemon listen for incoming connections:

.../luns/lun0> cd ../../portals
.../portals> create

Targetcli will tell you the IP and port where LIO is listening for incoming connections (defaults to 0.0.0.0 (all)). You will need at least the IP for the clients. The port should be the standard port 3260.

In order for a client/initiator to connect you need to include the IQN of the initiator in the target configuration:

...> cd ../../acls
.../acls> create iqn.2005-03.org.open-iscsi:SERIAL

Instead of iqn.2005-03.org.open-iscsi:SERIAL you use the IQN of an initiator. It can normally be found in /etc/iscsi/initiatorname.iscsi. You have to do this for every initiator that needs to connect. Targetcli will automatically map the created LUN to the newly created ACL.

Note: You can change the mapped LUNs and whether the access should be rw or ro. See help create at this point in the targetcli shell.

The last thing you have to do in targetcli when everything works is saving the configuration with:

...> cd /
/> saveconfig

The will the configuration in /etc/target/saveconfig.json. You can now safely start and stop target.service without losing your configuration.

Tip: You can give a filename as a parameter to saveconfig and also clear a configuration with clearconfig.

Authentication

Authentication per CHAP is enabled per default for your targets. You can either setup passwords or disable this authentication.

Disable Authentication

Navigate targetcli to your target (i.e. /iscsi/iqn.../tpg1) and:

.../tpg1> set attribute authentication=0

Warning: With this setting everybody that knows the iqn of one of your clients (initiators) can access the target. This is for testing or home purposes only.

Set Credentials

Navigate to a certain ACL of your target (i.e. /iscsi/iqn.../tpg1/acls/iqn.../) and

...> get auth

will show you the current authentication credentials.

...> set auth userid=<username in target>
...> set auth password=<password in target>
...> set auth mutual_userid=<username in initiator>  (optional)
...> set auth mutual_password=<password in initiator>  (optional)

The first two fields are the username and password of the target. The initiator will use this to log into the target. The last two fields (prefixed with "mutual_") are the username and password of the initiators (note that all initiators will have the same username and password). These two are optional parameters and it ensures that initiators will only accept connections from permitted targets.

Tips & Tricks

With targetcli sessions you can list the current open sessions.